Key

Key Function

LOCAL/REMOTE

To switch between keypad control and remote control

PRG

To switch the function, monitor the function and display the default function code respectively in the status of setting, operating and fault.

△

To change the function code and content in the status of setting, to change the output frequency in the status of operation.

▽

SET

To switch the function code and content in the status of setting, to read and store the function code and content.

RUN

To start the inverter’s operation in the condition of keypad control

STOP/ RESET

To stop the inverter’s operation in the condition of keypad operation. To stop the inverter’s operation in the event of fault.

Terminal Function Table

Category

Terminal

Signal Function

Function Description

control signal

FOR

forward / stop

to run forward while connected，to stop while disconnected

multi-functional contact input(P035～039)

X1

reverse / stop

to run reversely while disconnected，to stop while disconnected

X2

external fault input

to fail while connected，to be in a normal state while disconnected

X3

fault reset

to reset while connected

X4

multi-step speed speed command 1

effective while connected

X5

multi-step speed speed command 2

effective while connected

COM

switch input command terminal

—

analog input signal

+12V

+12Vpower supply output

analog command+12Vpower supply

VG

frequency input voltage

0～10V/100%

P042=0：VG effectiveP042=1：IG effective

IG

Frequency command input current

4～20mA/100%

GND

connecting terminal of shielding sheath of signal wire

—

switch output signal

TA2

operating signal(normally open contact )

to connect when operating

multi-function contact output(P041)

TC2

TA1

fault contact output

Between terminalTA1and C1. to fail while connected；to fail when terminal TB1and TC1 are disconnected

multi-function contact output(P040)

TB1

TC1

analog output signal

FM

frequency meter output

0～10V/100%frequency

multi-function analog value monitoring(P048)

GND

analog input command terminal

supplementary power supply

P24V

supplementary power supply

+24V

COM

Item

Specification

output

Rated output voltage

Maximum output voltage is same as power input voltage

output of adaptive motor (kW)

1.5

2.2

3.7

5.5

7.5

11

15

18.5

22

30

37

45

55

75

93

110

rated output current (A)

4.8

6.2

8

14

18

27

34

41

52

65

80

96

128

165

180

224

output of adaptive motor (kW)

132

160

185

200

220

245

280

315

355

400

500

560

630

710

800

1000

rated output current (A)

260

302

340

380

450

470

530

605

660

750

940

1050

1200

1300

1500

1860

rating

100％continuous

maximum overload current

Series：150% 1minute，180% 6minute（Series：120% 1minute，140%18minute）

power input

voltage / frequency

three phase 380V (+10%～-15%)  50 / 60Hz±5%

control characteristics

Frequency control range

0～400Hz

Frequency precision

digital command±0.01%(-10℃～+40℃)

frequency analysis setting

digital command0.1Hz； analog command0.1Hz

Output frequency analysis

0.1Hz

overload capacity

Series：rated output current 150%1minute，Series：rated output current 120%1minute

Frequency setting signal

0～+10V(20kΩ) 4～20mA(250Ω)

acceleration and deceleration time

0.1～3600minute (independent setting of accelerating time and reaccelerating time)

braking torque

additional braking resistance reaches125%

voltage / frequency characteristics

15 kinds of fixed V/F characteristics optional and any V/F characteristics

protecting functions

over voltage、under voltage、overload、thermionic relay、overheat、stall

environment

ambient temperature / humidity

-10℃ ～ +40℃ / 20～90% Rhino condensation

application area

indoor(no corrosive odor，Altitude is less 1000 meters or less，no dust、no corrosive odor, no direct sunlight

vibration

20Hz less than0.2g

protection level/cooling mode

IP50 for 11-200kW ,the rest is IP20/forced air cooling